Metal Structure
Strengthened by setting strong metal frame, its body is able to stand against any damage and crashes.
Perfect to Fly Anywhere
Perform excellent flight both outdoor and indoor without any problem.
Changeable Canopy
The canopy can be changed in various colors and shapes which give you more options.
Cool Performance
Proportional control system and co-axial structure enable it to hover stably in the air any height within control distance.
Durable Battery
The long life rechargeable Li-Po battery provides the strong power for a long time.

1)Three channels digital proportional control.
2)Proportional control system.
3)Control distance: 8-10m up
4)Made of a unique material to withstand crashes.
5)3CH control, 3D flight, go forward and backward, left and right, up and down.
6)Flying time 6-8 minutes.
7)Li-Po Battery.

Preparing for take OFF:
1) Extend the antenna on the radio control handset and switch the handset "ON"(LED on handset will flash once).
2) Switch the helicopter "ON"(Switch on bottom of the helicopter).
3) Place the helicopter on a flat, hard surface with the tail pointing towards you and the nose facing away from you.
4) Move the left joystick on the handset fully forward and fully backward, this will arm the controller and connect to the helicopter.

Launch time: Take Off and Landing
1) Move the left joystick slowly forward – the rotors will start to spin.
2) As you move the joystick past the halfway point the helicopter will lift off.
3) To ascend- move the left joystick further forward (Very small adjustment are needed as controls are sensitive).
4) To descend- slowly move the joystick backwards .

Steering:
1) To turn the nose of the helicopter left, move the right hand joystick to the left.
2) To turn the nose of the helicopter right, move the right hand joystick to the right.
3) To fly the helicopter forwards, move the right hand joystick forwards. The joysticks are very sensitive, small controlled movements should be used at all times.
4) To fly the helicopter backwards, move the right hand joystick backwards.

Landing:
To land the helicopter slowly move the left joystick backwards, before the helicopter touches the ground give the left joystick a quick burst upward to cushion landing.

Using the trim controls:
The Salvation 11 is fitted with three trim controls. These allow you to adjust the flight of the helicopter and remove any unwanted turning tendencies.

Trim 1: Located right of Throttle: Trim provides extra force to elevate helicopter. After fully charging the helicopter place trim to lowest position to dampen down throttle. When battery begins to lesser power, push trim fully forward for extra power.
NB*Ensure trim is returned to the lowest position before you begin to fly again, if too much power is transmitted to helicopter handset LED light will not turn "ON"
Trim2: Located left of Right Joystick: Trim provides extra force to move helicopter forwards and backwards.
Trim3: Located beneath Right Joystick: Trim removes unwanted spinning after takeoff .If helicopter spins right move trim control to the left and vice versa. If helicopter continues to spin after adjusting trim fully left or right, please refer to ‘How to fine tune The Salvation11

1) Ensure the helicopter ON/OFF switch is in the OFF position.
2) Plug the AC Charging Adaptor into a wall socket and ensure the socket is turned on. A red light on the charger should appear.
3) Connect the end of the charging cable to the charging socket on the side of the helicopter, the plug will easily connect to the socket and does not need to be forced together as it will only fit one way. When plugged into the helicopter the charger light should go OUT!!
4) Charging is complete when the LED on the charging adaptor lights up red. (around 45 minutes)
5) Switch off the AC Charging Adaptor at the wall socket and remove the charging cable from the Salvation 11.
6) LEAVE THE HELICOPTER FOR 2 MINUTES for battery to cool.
7) You’re now ready for take off.

Charging information: LED Indicators
1) Battery Charging ：LED on AC charging adaptor red
2) Battery Fully Charged ：LED on AC charging adaptor green
3) Charging Fault ：LED on AC charging adaptor flashing (the charging cable is not properly connected to the Salvation 11 or the Salvation 11 is switched on)
4) Radio Control Handset battery low ：LED on handset flashing and control distance reduced (replace battery).

Caution:
The Salvation 11 contains a Lithium Polymer battery that should not be discharged to a low voltage. To prevent this, recharge the helicopter when it no longer lifts off the ground.
1) Never leave your Salvation 11 charging near a fire or other source of heat.
2) Never leave the Salvation 11 unattended during charging.
3) Always disconnect from the mains once fully charged – do not leave to "trickle charge" as this may damage the battery.
4) Never disassemble the charger.
5) Only use the charger supplied with the Salvation 11.
6) NEVER STORE HELICOPTER WITHOUT CHARGING FIRST. This may damage the battery, always charge for 10mins minimum after use.